Инструменты пользователя

Инструменты сайта


lighthub

Различия

Показаны различия между двумя версиями страницы.

Ссылка на это сравнение

Предыдущая версия справа и слева Предыдущая версия
Следующая версия
Предыдущая версия
lighthub [2019/02/17 15:05]
admin
lighthub [2021/09/25 03:37] (текущий)
65.21.180.7 старая версия восстановлена (2021/09/19 10:25)
Строка 2: Строка 2:
 is Flexible, Arduino-Mega/Arduino DUE/ESP8266 open-software and open-hardware SmartHome controller. [RU](https://geektimes.ru/post/295109/) [HOME-site RU](http://lazyhome.ru) is Flexible, Arduino-Mega/Arduino DUE/ESP8266 open-software and open-hardware SmartHome controller. [RU](https://geektimes.ru/post/295109/) [HOME-site RU](http://lazyhome.ru)
 It may operate both:  It may operate both: 
- 
 * On [especially designed hardware board](http://www.lazyhome.ru/index.php/featurerequest) with 16 optocoupled digital inputs, 16 ESD protected digital/analog Inputs/outputs, 8 open-collector outputs (up to 0.5A/50V), DMX IN/OUT, MODBUS RTU and hardware 1-wire support circuit. * On [especially designed hardware board](http://www.lazyhome.ru/index.php/featurerequest) with 16 optocoupled digital inputs, 16 ESD protected digital/analog Inputs/outputs, 8 open-collector outputs (up to 0.5A/50V), DMX IN/OUT, MODBUS RTU and hardware 1-wire support circuit.
 * On plain Arduino MEGA 2560, Arduino DUE, ESP8266 and even on [Controllino](http://controllino.biz/) * On plain Arduino MEGA 2560, Arduino DUE, ESP8266 and even on [Controllino](http://controllino.biz/)
Строка 8: Строка 7:
  
 Lighthub allows connecting together: Lighthub allows connecting together:
- 
 * Contact sensors (switches, buttons etc) * Contact sensors (switches, buttons etc)
 * 1-Wire temperature sensors (up to 20 on single bus) * 1-Wire temperature sensors (up to 20 on single bus)
Строка 20: Строка 18:
  
 Where is possible both, to configure local control/mapping between inputs and outputs (light, floor heating thermostats) and remote control from MQTT enabled software. At the moment, LightHub tested with following set of complementary free software: Where is possible both, to configure local control/mapping between inputs and outputs (light, floor heating thermostats) and remote control from MQTT enabled software. At the moment, LightHub tested with following set of complementary free software:
- 
 * [Openhab or Openhab2 Smarthome software](http://www.openhab.org/) * [Openhab or Openhab2 Smarthome software](http://www.openhab.org/)
 Openhab provides own native mobile app both, for IoS and Android, and even allow you to use Apple's HomeKit to say "Siri, turn on light in bedroom" but requires some server to be installed (Raspberry PI with [Openhabian](https://docs.openhab.org/installation/openhabian) will good enough) Openhab provides own native mobile app both, for IoS and Android, and even allow you to use Apple's HomeKit to say "Siri, turn on light in bedroom" but requires some server to be installed (Raspberry PI with [Openhabian](https://docs.openhab.org/installation/openhabian) will good enough)
Строка 30: Строка 27:
  
 # [Please refer to our Wiki for insructions.](https://github.com/anklimov/lighthub/wiki/Configuring) # [Please refer to our Wiki for insructions.](https://github.com/anklimov/lighthub/wiki/Configuring)
- 
 * [Compiling and flashing](https://github.com/anklimov/lighthub/wiki/Compiling-and-flashing) * [Compiling and flashing](https://github.com/anklimov/lighthub/wiki/Compiling-and-flashing)
 * [Configuring](https://github.com/anklimov/lighthub/wiki/Configuring) * [Configuring](https://github.com/anklimov/lighthub/wiki/Configuring)
lighthub.1550405112.txt.gz · Последнее изменение: 2019/02/17 15:05 — admin